Flax weaves its way into cars and aircraft

By David Eldridge
EUROPEAN PLASTICS NEWS

Published: March 28, 2013 1:28 pm ET

Related to this story

Topics Automotive, Sustainability, Materials, Materials Suppliers, Aerospace

LEUVEN, BELGIUM — The drive to use green materials has led PSA Peugeot Citroën and Boeing Co. to explore applications for flax-based biocomposites.

Automotive Tier One supplier Faurecia has developed and patented a composite material called Flaxpreg which uses natural flax fibers in a thermoset resin matrix.

At a conference on flax and hemp organized by JEC Group and the European Confederation of Linen and Hemp (CELC) in Leuven, Belgium, in December 2012, the French company said it is working on a project with PSA Peugeot Citroën to use Flaxpreg in a car trunk load floor. Other project partners are the University of Reims and Lineo, a French company which produces flax prepregs.

The project was presented at the conference by Valérie Marcel, research engineer in Faurecia's interior systems division. The presentation was prepared jointly with Frédéric Rousseau, innovation project manager in the research and engineering department at PSA Peugeot Citroën.

The project is part of PSA's program to increase the amount of "green" materials in its cars. The sandwich panel floor being developed has a 65 percent green content and will be lighter than a comparable part which is currently produced using the Baypreg system. The targeted weight reduction is 2,000 g/m for the panel, which has flax-thermoset composite skins and a structured cardboard core.

Lineo is developing uni-directional (UD) flax tapes for the project to enable large volume production at a relatively low cost. The first mechanical performance tests, though, as discussed in the presentation, were on a panel made with woven flax fabric prepregs. This showed a good performance versus the Baypreg version.

Francois Vanfleteren, CEO of Lineo, told European Plastics News that mechanical performance using UD tape prepregs is expected to be similar or better than the fabric version. Lineo's UD tape production line for the project makes tape that is 40cm wide, but when scaled up for series production 1m wide tape will be possible.

According to Faurecia, PSA is expected to use the flax composite part in a demonstration car in 2014. Series production, if approved, would start in 2015 or 2016. PSA has exclusive rights to use the flax composite process for one car, after which Faurecia can use the process for other car manufacturers' applications.

In his presentation, Pedro Martin, material scientist in the materials and fuel cells department at Boeing Research & Technology Europe, discussed the Cayley project. In this, Boeing is working with partners to develop a biocomposite sandwich panel which can be used, for example, for sidewalls in the interior of its aircraft. The project has a target to produce panels in an automated one-step process at a rate of one panel every 15 minutes.

Boeing's partners in the Cayley project are Lineo, composites company Invent, based in Germany, and plastics research institute Aimplas, based in Spain. Boeing's work has focused on panels with skins made of flax in a thermoset resin matrix, and a foam core, while other partners are investigating PP and PLA.

"Fire resistance is the most challenging issue to overcome when working with natural fibres," said Martin.

In the project work, the flax fabrics were treated with halogen-free flame retardants. At laboratory scale, the biocomposite achieved compliance with fire resistance requirements of the US Federal Aviation Administration and the European Aviation Safety Agency.

But the project must still overcome other issues. Martin said it was working on the proof of concept for the prepreg system. Curing time for the thermoset resin is also very long and needs to be reduced, and shelf life for the prepreg needs to be increased.

During the project, Boeing produced a sidewall panel for a 737 aircraft made with the flax-thermoset composite. Using a vacuum bag process, the part was produced at full scale.

However, the production cycle was two hours due to a long curing time for the resin.

Martin said Boeing would work to solve these issues with the thermoset-based composite. The company may instead use the PP-based or PLA-based composite being developed by other Cayley partners. Whatever Boeing decides, the tough certification procedures of the aviation sector could take up to 10 years, said Martin.


Comments

Flax weaves its way into cars and aircraft

By David Eldridge
EUROPEAN PLASTICS NEWS

Published: March 28, 2013 1:28 pm ET

Post Your Comments


Back to story


More stories

Image

Barington may force a vote for Omnova board at annual meeting

January 28, 2015 3:52 pm ET

It looks like the battle between Omnova Solutions and an activist investor is heading to a vote.    More

Image

PolyOne sees sales, earnings per share climb, profit decline

January 28, 2015 3:00 pm ET

North American compounding leader PolyOne Corp. posted record adjusted earnings per share in 2014, even as the firm's sales saw modest growth and its ...    More

Image

China XD to catch up on Sichuan project

January 28, 2015 2:41 pm ET

Automotive compounder China XD Plastics Co. Ltd. (Nasdaq: CXDC) has been working on its fourth production base in Nanchong, Sichuan province since...    More

Image

Plastics help Volt hit new target

January 28, 2015 1:54 pm ET

The 2016 Volt, unveiled at the North American International Auto Show in Detroit in January, features a sportier exterior design — GM calls it...    More

Image

Sika opens negotiations to acquire Axson Technologies

January 28, 2015 12:17 pm ET

Specialty chemicals maker Sika AG has entered into exclusive negotiations with Axson SAS management and shareholders to acquire its epoxy and polyuret...    More

Market Reports

Plastics in Automotive: Innovation & Emerging Trends

This special report newly released by PN and sponsored by The Conair Group examines current trends in the use of plastics in automotive, materials innovations and the changing landscape. It includes a review of legislative/regulatory activity impacting vehicle development and lightweighting, market opportunities & challenges for mold and toolmakers, innovative design strategies being implemented by major OEMs and suppliers, as well as a review of key indicators in Canada, Mexico, Brazil and China.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Upcoming Plastics News Events

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events