International plastics markets try to find footing

By Frank Esposito
Senior Staff Reporter

Published: March 29, 2013 1:58 pm ET
Updated: March 29, 2013 5:35 pm ET

Related to this story

Topics Materials, Materials Suppliers

HOUSTON — Winds are blowing through international plastic markets in the Middle East, Europe and Latin America. Top officials with plastics and chemicals firms in those regions tried to tame those winds at the IHS World Petrochemical Conference, held March 20-21 in Houston.

Growth in the Middle East now is higher than it is in mature economies such as those in Europe, said Moayyed Al-Qurtas, vice chairman of plastics and chemicals maker Tasnee of Riyadh, Saudi Arabia. The region has a feedstock fuel advantage through ample supplies of natural gas and has built some of the largest petrochemical plants in the world, he added.

The Middle East also has access to financing and growing markets, according to Al-Qurtas. "Some are not looking to the potential of the region," he said. "We are within 1,500 miles of 28 percent of the world's population and 11 percent of the world [gross domestic product], not counting Europe. Our population is growing and our users are becoming more sophisticated."

The Middle Eastern market has come a long way since the 1960s and 1970s, when producers were looking for ways to monetize natural gas that was being burned off in flares. This growth led to Tasnee opening in 2004. The firm now makes high density and low density polyethylene, as well as polypropylene, acrylic acid and related products and compounds.

The next stage of the region's development will require producers moving into specialty chemicals and differentiated commodities, including engineering resins and performance polymers such as polyurethane, Al-Qurtas said.

Greater challenges exist in Europe, where slowing demand and increased imports likely will lead to some plastics and chemicals production being rationalized in the next few years, said Total SA's Graeme Burnett. Burnett serves as vice president of refining and petrochemicals in the Americas for Total, the oil and gas giant based in Colombes, France.

The need to rationalize likely will affect smaller, non-integrated plants, Burnett said. But closing plants in Europe is a lengthy process that can take several years because of labor agreements.

Total has done its part to invest in larger plants by spending more than $5 billion on upgrades to its plants in Normandy, France, and Antwerp, Belgium. Europe remains home to 530 million people and 24 percent of global GDP, he added, and has more than 100 billion pounds of annual resin demand.

Imports of plastics and chemicals into Europe are expected to increase by at least 2 billion pounds annually over the next few years — largely from cost-advantaged new production in North America and the Middle East. But Burnett said there are strategies European producers still can pursue.

"We understand the needs of the European customer and can develop value-added products such as expanded polystyrene and metallocene polyethylene and polypropylene," he said.

Latin America — with a population of almost 600 million that is growing faster than the U.S., Canada and Europe — is providing opportunities for the region's plastics and chemicals makers, according to Grupo Idesa SA de CV's José Luis Uriegas. Uriegas serves as CEO of the firm, a petrochemicals conglomerate based in Mexico City.

Latin America, like the U.S., is benefiting from natural gas supplies that are providing low-cost feedstocks. The region is home to countries with three of the world's 10 largest natural gas reserves — Argentina (third), Mexico (fourth) and Brazil (10th).

Natural gas-based ethane will account for 41 percent of Latin America's ethylene production by 2016, up from its 2012 total of 32 percent, Uriegas said. Mexico now bases all of its ethylene production on ethane. Venezuela has the region's highest petrochemical cost advantage, followed by Mexico.

Foreign trade remains very important for Latin America as a region. Mexico relies on foreign trade for almost 60 percent of its GDP. Argentina, Venezuela and Colombia each have about one-third of their economies tied to foreign trade. Brazil, with a larger domestic economy gets only about 20 percent of its economic activity in that manner.

Grupo Idesa is doing its part to capitalize on low-cost feedstocks by joining Braskem SA in the Ethylene XXI project. Ethylene XXI is a $4.6 billion petrochemicals project that's set to come on line by the end of 2014, producing high density and linear low density PE and ethylene feedstock.


Comments

International plastics markets try to find footing

By Frank Esposito
Senior Staff Reporter

Published: March 29, 2013 1:58 pm ET
Updated: March 29, 2013 5:35 pm ET

Post Your Comments


Back to story


More stories

Image

2014 leaves some resin firms in the black while others struggle

January 23, 2015 2:37 pm ET

On the financial side, 2014 was good for Hexcel Corp., so-so for Celanese Corp. and it could have been better for Omnova Solutions.    More

Image

Clariant's ColorForward predicts future consumer trends

January 23, 2015 1:33 pm ET

Clariant International Ltd. is marking a decade of color forecasting with the 10th edition of its ColorForward program.    More

Image

The future for PolyOne is colorful

January 23, 2015 1:28 pm ET

PolyOne Corp. is writing four color stories for 2016.    More

Image

Mexico's Polymer Solutions looks to grow, expand offerings with name change

January 23, 2015 12:03 pm ET

British biodegradable additives developer Symphony Environmental Technologies plc's Mexico distributor has changed its name from Plásticos...    More

Image

Drop in oil leads to resin pricing plunge

January 22, 2015 3:16 pm ET

In most Decembers, resin makers try to focus on the holidays and on spending time with their families. This improves their mental well-being and also ...    More

Market Reports

Plastics in Automotive: Innovation & Emerging Trends

This special report newly released by PN and sponsored by The Conair Group examines current trends in the use of plastics in automotive, materials innovations and the changing landscape. It includes a review of legislative/regulatory activity impacting vehicle development and lightweighting, market opportunities & challenges for mold and toolmakers, innovative design strategies being implemented by major OEMs and suppliers, as well as a review of key indicators in Canada, Mexico, Brazil and China.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Upcoming Plastics News Events

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events