Bemis and Milacron show off 1,500-ton hybrid press

Published: April 29, 2013 5:19 pm ET
Updated: April 29, 2013 5:30 pm ET

Image By: Plastics News Gary Vande Berg

Related to this story

Topics Coinjection, Injection Molding, Machinery
Companies & Associations Milacron LLC

BATAVIA, OHIO — It might be a match made in injection molding heaven.

Bemis Manufacturing Co. has teamed up with Milacron LLC to develop what they're calling the industry's largest Servo hybrid coinjection machine, the 1,500 ton Maxima G Servo.

The machine was one of more than 20 on display at an open house at Milacron headquarters, held April 24-25 in Batavia.

According to Milacron, the machine is energy efficient — it uses less than half the energy of comparable hydraulic press — and is the industry's most versatile multi-component Servo machine. It has seven unique process capabilities that can be run a single platform; the system can be configured for sequential or simultaneous injection, stack molding, multi-component and coinjection molding, among other processes.

The machine is the latest partnership between the two companies, who have been working together on coinjection technology for about a decade.

In essence, coinjection, or encapsulation, is molding one material inside of another, creating a part with an outer skin and an inner core.

The technology was patented in the late 1950s and primarily used in Europe, but Sheybogan Falls, Wis.,-based Bemis started working with it in the early '90s. The company acquired a used 700 ton Battenfield machine and was "up and running. Crawling is more like it," said Gary Vande Berg, vice president of engineering for Bemis.

"You've heard the term invention is ugly? This was ugly," he joked in a presentation at the open house.

So Bemis sat down to essentially reinvent coinjection technology. In 1994, they approached Milacron with their results and asked them to design and build a machine. The result was a 725 ton coinjection machine, which ran at the 1994 NPE Show and is still running 24/7, Vande Berg said.

The company now has 32 coinjection machines, ranging from about 300 to 6,600 tons, he said.

The technology allows Bemis to successfully marry business and sustainability.

"You can do anything you want for the environment, but if your business doesn't survive, it isn't going to do much good," Vande Berg said.

Coinjection molding can be used to incorporate recycled or reground "junk" material in plastic parts without sacrificing aesthetics or physical properties.

Bemis can now make coinjected toilet seats with 75 percent recycled content -- 25 percent in the skin and 30 to 50 percent in the core, Vande Berg said.

The company also molds parts for John Deere tractors, using a more expensive, glossy material on the outside and a cheaper material on the inside.

Coinjected parts also have better physical impact properties. They can be up to 2.5 times stronger than a typical monoinjected part, and "that's with junk material on the inside," he said.

Bemis struggled to make a hood for a lawn and garden tractor that had both the necessary impact strength and a glossy finish -- when they tweaked the material to improve gloss, impact strength decreased, and vice-versa, he said. The solution was a coinjected part with an ABS core and a glossy exterior that was also cheaper to manufacture, he said.

Vande Berg also gave examples of how Bemis uses coinjection molding with controlled breakout techniques and gas-assist molding to make chair arms, steering wheels and refrigerator handles.

"You can have totally different physical properties within the same part coming out [of the machine] at the same time," he said.

The company's big revelation came when they realized "coinjection machines weren't really coinjection machines, they were multi material machines," he said.

With help from Milacron, Bemis started working with two-shot molding, then on to sequential injection, then on to using a three-barrel system. A four barrel machine is in the works, he said.

All of these different processes can be run on the same machine with just a few changes in software, he said.

When you take all the different options into consideration, Bemis can offer customers more than 51 different ways to mold a part.

"That doesn't mean we're still always going to be cheapest. But if you've got 51 ways to look at a part, that sure beats two ways to look at a part," he said.

It also allows the company to offer parts with a desired "weird factor."

"If we cannot apply a minimum of one weird factor, we don't quote the part. End of discussion," Vande Berg said. "We're not a clip and ship company. If we can't apply technology, it's not our business."


Comments

Bemis and Milacron show off 1,500-ton hybrid press

Published: April 29, 2013 5:19 pm ET
Updated: April 29, 2013 5:30 pm ET

Post Your Comments


Back to story


More stories

Image

Cambro investing $30.4 million in new N.C. injection molding plant

April 18, 2014 2:36 pm ET

Foodservice products manufacturer Cambro Manufacturing Co. Inc. plans to set up a satellite production and distribution operation in Mebane, N.C., to ...    More

Image

Increased orders prompt Georg Utz to add capacity, equipment in Indiana

April 18, 2014 12:20 pm ET

Plastic totes and tray orders have picked up to the point where manufacturer Georg Utz Inc. has added machines, silos and material feed systems to...    More

MGS buying N.Y. medical molding plant from Hospira

April 17, 2014 10:19 pm ET

MGS Manufacturing Group is purchasing the Buffalo, N.Y., injection molding facility and related product line of Hospira Inc., effective July 1. Terms ...    More

Image

German auto supplier Dr. Schneider opens second US plant

April 17, 2014 12:57 pm ET

Dr. Schneider Kunststoffwerke GmbH, a German supplier of plastic interior auto parts, has opened a $29 million manufacturing plant in Russell Springs,...    More

Image

Top export markets for Italian machinery and molds

April 17, 2014 9:00 am ET

Top export markets for Italian machinery and molds    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report provides analysis and discussions of economic and political conditions, market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as strategies being implemented by thermoformed packaging companies. In addition, there are reviews of 25 leading thermoformers in the packaging segment, assessing their growth initiatives and performance metrics over 10 years.

Learn more

Automotive Market Review and Outlook 2014 The Americas

This 75-page report features in-depth analysis of the automotive industry for the Americas. It includes discussions of market trends, legislative/regulatory activity impacting production and threats as well as design strategies being implemented by the major automakers. Detailed charts and data tables outline North American automotive production over the last five years.

Learn more

Plastics Building & Construction Market Review and Outlook 2014 with MS Excel chart data

This report provides in-depth analysis of the plastic building and construction market for North America, including discussions of trends, opportunities, threats and the latest developments in construction trends that impact plastics processors.

Learn more

Upcoming Plastics News Events

May 6, 2014 - May 8, 2014Plastics in Medical Devices 2014

May 12, 2014 - May 12, 2014Plastics News Brazil Pharma Summit

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

February 3, 2015 - February 7, 2015Plastics News Executive Forum 2015

More Events