HDPE, PP resin prices inch up in month of June

By Frank Esposito
Senior Staff Reporter

Published: July 3, 2013 4:15 pm ET
Updated: July 3, 2013 4:24 pm ET

Related to this story

Topics Polyethylene, Materials Suppliers, Resin Pricing, Polypropylene
Companies & Associations Chevron Phillips Chemical Co. LP

AKRON, OHIO — Supply issues led North American prices for polypropylene and high density polyethylene resin to climb in June.

PP prices moved up an average of 3 cents per pound, as three companies now have reported production challenges. HDPE prices got nudged up an average of 2 cents per pound as a result of supply issues on both the resin and feedstock sides, and stronger demand.

Regional PP supplies have been tightened by unexpected outages at plants operated by Formosa Plastics Corp. USA in Point Comfort, Texas, and by Pinnacle Polymers in Garyville, La.

Formosa ended force majeure conditions on PP last week, but Phillips 66 Co. became the latest PP maker with supply problems when its supply of propylene monomer was impacted by a deadly June 13 explosion at an olefins plant operated by Williams Cos. in Geismar, La. The resulting outage of propylene has led Phillips 66 to limit production of PP at its plant in Linden, N.J.

PP prices in the region had surged 15 cents per pound in the first two months of 2013 but had fallen 17 cents since then. The June hike leaves prices up a net of 1 cent per pound so far this year.

U.S./Canadian PP demand remained weak through April, according to the American Chemistry Council in Washington, falling more than 5 percent vs. the same four months in 2012. A domestic sales drop of almost 4 percent was amplified by a plummet of almost 40 percent in export sales.

Domestic sales of PP into injection molded consumer products — including housewares — fell more than 5 percent through April, while sales to domestic resellers dipped almost 19 percent, according to ACC.

"On the PP side, there have been a host of supply issues, both monomer and polymer-related," resin market analyst David Barry said in an email. "The explosion at Williams' olefins plant has caused the [polymer-grade propylene] market to be tighter than expected.

"There's a big question mark about PP demand as the summer goes along, because it appears that a lot of buyers took the opportunity to pre-buy in May and June," added Barry, who's with the PetroChem Wire LLC consulting firm in Houston. "But in the near term [PP supply] is very tight, and several producers have already indicated they will be looking to expand margins on their monomer-plus contracts by 2 cents per pound in July and August."

For HDPE, the 2-cent hike is the first price move since 9 cents in increases took hold earlier in the year. Prices now are up a total of 11 cents in 2013 for a hike of almost 13 percent.

An outage at Formosa's Point Comfort plant has impacted regional HDPE supply, although the firm last week also lifted force majeure conditions on HDPE there. The situation at the Williams plant in Geismar — which had more than 1 billion pounds of annual ethylene feedstock capacity — could create pressure in the PE field.

Regional HDPE supplies also have been affected by a force majeure situation at Chevron Phillips Chemical Co. LLC's Cedar Bayou plant in Baytown, Texas. The firm experienced a "minor emissions event" on May 9 and 10 when small amounts of hexene, pentane and gaseous ethylene were released.

On May 14, officials said Chevron Phillips — based in The Woodlands, Texas — would "return to full polyethylene deliveries as soon as possible." However, officials declined to comment on the situation July 3.

Regional HDPE makers were enjoying a solid year through April, with sales up more than 6 percent, according to ACC. Export sales growth of almost 22 percent boosted domestic sales growth of almost 4 percent. Domestic HDPE sales into injection molding applications climbed 7 percent in that four-month period.

Total regional PE sales for May — including low and linear low density PE — clocked in at more than 3.4 billion pounds, making it the best sales month for the material since June 2012.

"There was a significant drawdown of [PE] inventories as industry operating rates were 2-4 percentage points below the 12-month average in May," Barry said. "So PE was tightening in May, and there is not much evidence that demand slowed down significantly in June." "That being said, prices seem to have reached a point where it will become difficult to push them up much further," he added, since several buyers "are expecting PE prices to correct downward" in July.


Comments

HDPE, PP resin prices inch up in month of June

By Frank Esposito
Senior Staff Reporter

Published: July 3, 2013 4:15 pm ET
Updated: July 3, 2013 4:24 pm ET

Post Your Comments


Back to story


More stories

Image

EPA fines RI polymer company

August 29, 2014 1:20 pm ET

A Rhode Island polymer manufacturer has reached a $60,000 settlement with the U.S. Environmental Protection Agency (EPA) for violating federal clean...    More

Image

Updating a travel icon for the professional millennial

August 29, 2014 11:44 am ET

As part of a drive to expand its customer base to include more millennials, Airstream Inc. turned to the Columbus College of Art & Design's...    More

Image

Chinese compounders seek market shares, often at the expense of margins

August 29, 2014 10:02 am ET

China's largest compounder, Kingfa Sci. & Tech. Co. Ltd., as well as its more automotive-focused counterparts Shanghai Pret Composites Co. Ltd. and...    More

Image

PP prices rise 5 cents

August 28, 2014 3:59 pm ET

After a one-month break, volatility has returned to the North American polypropylene resin market, with prices increasing by an average of 5 cents...    More

Image

DuPont fined for 2010 chemicals release

August 28, 2014 1:37 pm ET

DuPont Co. has been fined almost $1.3 million for the release of several chemicals — including plastics feedstock phosgene — at its plant ...    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events