Urethane product firms wary of MOCA bills

Mike McNulty
RUBBER & PLASTICS NEWS

Published: July 8, 2013 12:38 pm ET
Updated: July 8, 2013 12:40 pm ET

Related to this story

Topics Public Policy, Materials, Materials Suppliers, Government & Legislation

LAS VEGAS — Another round of battles concerning the polyurethane curative methyl-bischloroaniline, commonly called MOCA, could be coming.

The European Union is moving ahead with REACH legislation that would ban MOCA in countries that adopt the EU regulations, according to Donald Gallo, legal counsel for the Polyurethane Manufacturers Association (PMA) and an attorney with the Waukesha, Wis.-based law firm of Reinhart Boerner Van Deuren S.C.

Meanwhile, the European Chemicals Agency has selected MOCA from its list of very high concern substances and recommended it for inclusion in Annex XIV, he said.

Should MOCA end up in Annex XIV, the curative would be banned without the authorization of the EU and other countries that adapt REACH legislation, he said at PMA's annual conference, held recently in Las Vegas.

There is fear within the association that the U.S. Environmental Protection Agency, via the Toxic Substance Control Act, and the Canadian government could adapt the REACH approach in banning the use of MOCA, according to Gallo.

At the very least, the REACH plan could "impose onerous restrictions at some point in the future on the way to an eventual ban," said Mike Kocak, the incoming president of the PMA and quality assurance manager of C.U.E. Inc., headquartered in Cranberry Township, Pa.

"We are very concerned because it threatens the use of a chemical that is important to our business, and … we are taking steps to develop information that addresses expressed and legitimate concerns that have been raised by the EU," Gallo said.

In addition, the American Conference of Governmental Industrial Hygienists probably will lower the Threshold Limit Values/Short-Term Exposure Limits for TDI (toluene diisocyanate) to the point that monitoring badges currently in use will not be usable, Kocak said.

"Our concern is that lack of affordable, consistent individual monitoring that the badges provided may make the exposure situation worse, not better," he said.

PMA has developed programs for the safe use of MOCA in the US and Canada, including employee urinalysis monitoring for which the organization has between 30-40 years of monitoring data, Gallo said.

The programs include work surface swipe testing to address dermal contact and include information on proper protective clothing and ventilation in the work place.

Worker exposure can be minimized by following the PMA's suggested safe work practices, Kocak advised.

Because of the economics of other curatives and the properties of MOCA, "we feel the need to protect MOCA as a curative for the sake of the castable polyurethane industry," according to Gallo.

If the cost of castable polyurethane increases, the PMA's legal counsel said, the markets will adjust and demand may decrease.

"We have conducted tests on articles (or finished parts) made from castable polyurethane and have found the levels of free MOCA in a fully cured article to be quite low and well within acceptable levels over quite a range of curing methods and cure times," Gallo said.

PMA plans on providing information to regulators that demonstrates "best management practices can be used and are currently being used to protect employees and the community," he said.

Not long after the PMA was formed in the early 1970s, the use of MOCA was threatened by government agencies that attempted to ban the polyurethane curative.

The trade association took on EPA, the Occupational Health and Safety Administration and other entities and won numerous battles that followed.


Comments

Urethane product firms wary of MOCA bills

Mike McNulty
RUBBER & PLASTICS NEWS

Published: July 8, 2013 12:38 pm ET
Updated: July 8, 2013 12:40 pm ET

Post Your Comments


Back to story


More stories

Image

Audacious vandal stuns Taipei Plas

September 29, 2014 4:59 pm ET

Melodrama erupted at the traditionally tranquil Taipei Plas trade show on Sept. 28 when a mysterious intruder flung red paint at the Baumüller...    More

Image

Germans, Chinese question Plastindia move to Gujarat

September 29, 2014 4:39 pm ET

Two major international partners of the Plastindia trade show have raised serious concerns about the show organizer's decision to move it to another...    More

Image

Asahi Kasei breaks ground on Alabama compounding plant

September 29, 2014 5:39 pm ET

Asahi Kasei Plastics North America will be able to solve two problems at once with a new compounding plant in Athens, Ala.    More

Image

EEOC suing movable wall maker Hufcor

September 29, 2014 3:09 pm ET

Movable wall and partition maker Hufcor Inc. is facing a federal lawsuit from the U.S. Equal Employment Opportunity Commission after violating...    More

Image

DuPont shifting Teflon production in China

September 29, 2014 2:35 pm ET

DuPont Co. will spend more than $15 million to improve its fluoropolymer product offerings in China.    More

Market Reports

Plastics in Mexico - State of the Industry Report

This report analyzes the $20 million dollar plastics industry in Mexico including sales of machinery & equipment, resins and finished products.

Our industry analysis highlights macro industry trends and micro trends faced by companies that do business in Mexico. The report also provides key industry statistics and forecasts to anticipate future industry expansion.

Learn more

Plastics Caps & Closures Market Report

The annual recap of top trends and future outlook for the plastics caps & closures market features interviews with industry thought leaders and Bill Wood’s economic forecast of trends in growing end markets. You will also gain insight on trends in caps design, materials, machinery, molds & tooling and reviews of mergers & acquisitions.

Learn more

Injection Molders Market Report & Ranking 2014

This special package contains our 132-page 2014 Market Report on the Injection Molding segment and our exclusive 2014 RANKINGS database of 500+ Injection Molders for a discounted package price.

Learn more

Upcoming Plastics News Events

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events