Architects eye plastics for sustainability

By Angie DeRosa
Conference Director

Published: July 31, 2013 4:10 pm ET
Updated: July 31, 2013 4:20 pm ET

Image By: Resysta North America The facade of this building in Vietnam uses Resysta's vinyl products, which allow architectural flexibility and replicate the look of wood

Related to this story

Topics Construction, Sustainability

DENVER — Plastics processors want to get the attention of architects, and plenty of construction products suppliers were on hand at the American Institute of Architects Convention, held June 19-22 at the Colorado Convention Center in Denver.

Although the event largely was focused on commercial construction, residential crept its way in, too, and both segments hold opportunity for suppliers and converters.

Total U.S. construction starts in 2013 are expected to rise 6 percent, according to the 2013 Dodge Construction Outlook. That same report predicted that single-family housing would grow 21 percent in units to 615,000. Multifamily housing will rise 14 percent to 285,000 units; and commercial building will increase 12 percent to 419 million square feet.

Still, the adjustment will be a "new normal." Builders and the supply chain are struggling with price sensitivity, price compression and margin compression. One source said that vinyl siding sales were down as much as 18 percent in May vs. the year-ago period and that sales were down 6 percent for the year to date. Expandable polystyrene resin manufacturers experienced their worst first quarter since 2009.

In housing activity, foreclosures in single-family homes have been easing, home prices are stabilizing and anyone who has purchased a home in the last year likely has benefited from low mortgage rates. Houses also are getting smaller. If a family might have lived in a 3,500-square-foot home, now that family might be more likely to want a 2,000-square-foot space.

"Directionally, it's good," said Pat Culpepper, president of Progressive Foam Technologies Inc., in Beach City, Ohio. "But the oxygen is not on. Do not take off your mask or you will suffocate."

Indeed, it's the "proceed with caution" mindset that was being espoused in the exhibit hall but supported by the idea that plastics technologies will grow in this stabilizing market.

One mechanical contractor who was representing the Radiant Professionals Alliance said he had to be convinced of the benefits of cross-linked polyethylene tubing for radiant floor heating years ago. Now, it is the primary material he uses, and he expects plastics technologies will continue to grow in building and construction.

BASF Corp. of Florham Park, N.J., was demonstrating its closed-cell spray polyurethane foam insulation, while DaVinci Roofscapes LLC of Kansas City, Kan., was touting the benefits of injection molded roof panels that replicate the appearance of wood shake.

DaVinci said the panels help builders achieve sustainability goals — a popular feature, since architects and builders are under pressure to improve energy efficiency and account for life-cycle analysis preferences.

DaVinci uses a proprietary polymer blend in molding the panels.

Elsewhere in the exhibit hall, PVC had its own cheerleaders. Several officials were focusing on the material's recyclability, durability and safety.

"The architects like our product," said Arne Zenneck, head of sales for Resysta North America Inc. of Chino, Calif., which sells profiles extruded from a combination of 40 percent PVC, 25 percent rice hulls, 20 percent calcium carbonate and 10 percent additives.

Resysta claimed a prime spot in the exhibit hall within the wood section. The product is making its way in the North American market, where customers include Starbucks Coffee Co. and P.F. Chang's China Bistro Inc.

Recently, the company was awarded a coveted Red Dot Product Design Award for its applications in the marine industry. The profiles are being used in exterior and interior installations, including decking, façades and furniture.

"Wherever they spec wood or tropical hardwoods, we want them to spec our product," Zenneck said. "We really try to replicate the wood look and the market we are after is tropical hardwoods. Although we have to admit that we are vinyl."

When an architect in Vietnam wanted to spec wood for a façade, Resysta officials talked him into using Resysta instead.

At the booth for the Alexandria, Va.-based Vinyl Institute, profiles from Resysta were placed side-by-side to create the blue, orange and green flooring to brand the booth. Communicating the virtues of vinyl in building and construction has been a difficult process, VI officials said.

What potential users need to hear is the sustainability aspects of vinyl, including the recyclability.

The goal for the inventor of Resysta was to make a greener vinyl. The inventor is from Singapore and his family runs PVC extrusion operations.

In the world of polyurethanes, Carter Millwork Flexible Molding of Linwood, N.C., was showcasing its architectural flexible molding that replicates the look of wood. Education is the focus for officials there.

"The bottom line is, we're chemistry," said David Welborn, vice president of sales, in a June 21 interview at Carter's booth. "It's all about awareness and education."


Comments

Architects eye plastics for sustainability

By Angie DeRosa
Conference Director

Published: July 31, 2013 4:10 pm ET
Updated: July 31, 2013 4:20 pm ET

Post Your Comments


Back to story


More stories

Image

Updating a travel icon for the professional millennial

August 29, 2014 11:44 am ET

As part of a drive to expand its customer base to include more millennials, Airstream Inc. turned to the Columbus College of Art & Design's...    More

Image

Green trend boosts plastic building materials business in China

August 29, 2014 9:42 am ET

The greening of China's domestic building materials market is giving the plastics industry a boost.    More

Image

Plastics News Now: Students set sail on PET boat

August 28, 2014 6:00 am ET

A toymaker moves production to the United States from China, an ice bucket maker takes the ALS challenge with a twist and students made a boat nearly ...    More

Image

Truce? ACC, US Green Building Council agree to work together on LEED

August 28, 2014 12:08 pm ET

The American Chemistry Council (ACC) and the U.S. Green Building Council (USGBC) announced Aug. 27 that they will be working together on a new...    More

Image

Bag usage drops 71% in Northern Ireland

August 28, 2014 10:41 am ET

A shopping bag fee in Northern Ireland has resulted in a 71.8 percent reduction in bag numbers in its first year of operation.    More

Market Reports

Thermoformed Packaging 2014 Market Review & Outlook North America

This in-depth report analyzes economic and market trends, legislative/regulatory activity impacting supply and demand, business opportunities and threats, materials pricing, manufacturing technology, as well as growth strategies being implemented by thermoformed packaging companies.

Learn more

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events