Akron Polymer installs film casting line

By Bill Bregar
Senior Staff Reporter

Published: October 9, 2013 5:20 pm ET
Updated: October 9, 2013 5:26 pm ET

Akron Polymer feature

Image By: Plastics News photo by Bill Bregar Akron Polymer Systems President and CEO Frank Harris in his firm's clean room, home to its new film casting line

Related to this story

Topics Aerospace, Automotive, Medical, Film & Sheet

AKRON, OHIO — Akron Polymer Systems Inc. has installed a solvent film casting in a new 800-square-foot clean room at the specialty polymer development company.

The machine from Frontier Industrial Technology Inc., which can make cast film up to 18 inches wide, will go into production in October. APS is installing a new laminator on the line.

Before starting up the clean room and film line, Akron Polymer Systems had to outsource that production to toll film makers, according to President and CEO Frank Harris.

The cast film floats on a blanket of air during the process, he said.

Frontier Industrial Technology of Towanda, Pa., custom-made the film line, which is made of stainless steel for clean room use.

Akron Polymer Systems also is building a smaller clean room for small-scale, hand-casting of film.

Film is a key part of several Akron Polymer Systems projects, including substrates for flat panel displays and polymers for membranes used in gas separation, water purification and fuel cells.

But Akron Polymer Systems is involved in other product developments as well, such as biodegradable, high-strength polymers, nanotechnology, thermally stable composite resins for missile nose cones, and biomedical innovations such as a plastic implant that enhances bone growth in cancer patients. APS is making the polymer used in research at Methodist Research Hospital in Houston.

Akron Polymer Systems is housed in a 16,000-square-foot building full of reactors, compounding lines and laboratory equipment and the new cast film line. Beyond the equipment, the firm has some intellectual polymer-science firepower, as nine of the 12 employees have PhDs.

The company makes batch sizes of the new polymers, working on joint product and process development, does custom synthesis of new polymers and monomers for large corporations, and imports high-performance polymers and additives.

Harris said film and coatings played an important role from the beginning of Akron Polymer Systems, to develop second-generation film for liquid-crystal displays.

In the late 1990s, University of Akron researchers developed the first generation of the film. By the early 2000s, the university had licensed technology to a maker of jet cockpit displays.

Another licensing deal followed with a Japanese maker of large-screen TVs.

Akron Polymer Systems also worked on technology called in-plane switching films, winning a grant from Ohio's Third Frontier program. Film made by in-plane switching lines up the liquid crystals to give a vivid, clear picture, improving off-angle viewability, such as looking at the screen from a side angle. Harris credits a grant from Third Frontier for helping Akron Polymer Systems in its early days — and keeping the high-level jobs in Akron.

"The Third Frontier was very important in starting our business," he said.

APS uses polymer science to manipulate polymers to produce high-performance materials, sometimes for harsh operating conditions. For example, the membranes for fuel cells must withstand very high temperatures.

Harris and Stephen Chen, both polymer science professors at the University of Akron, founded Akron Polymer Systems in 2002. Chen now is the dean of UA's College of Polymer Science and Polymer Engineering. Harris, who retired from the university in 2005, is emeritus distinguished professor of polymer science and biomedical engineering.

Akron Polymer Systems uses a long list of advanced materials, including polyimides, polysulfone, composites and biodegradable polymers for medical.

The company's income sources are royalty payments on research and development, government funding, custom synthesis of pilot-plant quantities, sales of imported specialty chemicals and consulting services.


Comments

Akron Polymer installs film casting line

By Bill Bregar
Senior Staff Reporter

Published: October 9, 2013 5:20 pm ET
Updated: October 9, 2013 5:26 pm ET

Post Your Comments


Back to story


More stories

Image

Bankruptcy court confirms GSE reorganization plan

July 29, 2014 4:01 pm ET

The U.S. Bankruptcy Court in Wilmington, Del., has confirmed the reorganization plan for geomembranes maker GSE Environmental Inc.    More

Image

Vinyl siding's lead slips, but industry pushing back

July 29, 2014 2:04 pm ET

Vinyl siding continues to be the top cladding choice for home builders and remodelers but fiber cement is gaining ground — at an alarming rate...    More

Image

Magna expanding interiors site in Slovakia

July 29, 2014 1:47 pm ET

Magna International Inc. plans to nearly double the size of its manufacturing facility in Trnava, in western Slovakia, to accommodate new automotive...    More

Image

Two medical device makers add specialty products through acquisitions

July 28, 2014 3:02 pm ET

The medical merger mania continues this summer as two more medical device manufacturers are swallowed up by bigger competitors.    More

Image

Material Insights: Bioplastics firms win government funding

July 28, 2014 12:51 pm ET

Also this week, a study takes a look plastic at the ocean surface and comes away with a surprise finding, and new materials capacity announced.    More

Market Reports

Plastics Recyclers Data Report & Directory

This exclusive MS Excel database contains all the companies from Plastics News' ranking of top North American Recyclers and Brokers by reprocessed volume and also includes a directory with materials processes, services offered and company contact information. Data is based on primary research by PN editorial staff.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events