Growth slows sharply for China's plastics processors

By Steve Toloken
Staff Reporter / Asia Bureau Chief

Published: November 8, 2013 12:46 pm ET
Updated: November 8, 2013 12:48 pm ET

Related to this story

Topics China, Financial

FOSHAN, CHINA — Rising costs and economic challenges caused China’s plastics processing industry to see its growth slow to about 5 percent in the first nine months of the year, prompting the head of the country’s largest plastics association to make a forceful call for companies to innovate and adopt new technology.

That estimated 5 percent increase in manufacturing output of plastics products is down from 8.9 percent in 2012, which itself was well off the 20+ percent growth in 2011 and the previous several boom years, said Qian Guijing, president of the Beijing-based China Plastics Processing Industry Association.

China’s plastics industry will have to get used to a period of slower growth, he suggested, although even 5 percent would still beat last year’s 3 percent increase in worldwide plastics production.

“A lot of people have this fantasy that after the financial crisis, we can have another era of high growth,” said Qian, in a speech at the 2013 Plastics Industry New Materials, New Processing and New Equipment Industry Summit, held Nov. 8-9 in Foshan. “We have to adjust and adapt to this period.”

By adjust, Qian said he means the industry needs to change from an investment-based model focused on competing on lower costs, to one based on better use of technology, such as energy-saving equipment, advanced foamed plastics to lightweight parts for cars and other industries, high-barrier films, micromolding and 3-D printing.

“In the past we relied on enlarging the investments but this method cannot continue in the future,” he said. “We can never exaggerate the significant meaning these technologies have for our industry.”

He said the processing industry’s challenges are well catalogued, including rising costs from higher wages in China, excess capacity that hurts profit margins, tougher environmental regulations and troubles in the world economy since the 2008 financial crisis.

“The financial crisis had a tremendous impact on us,” he said. “We have slowed down the speed of our development.”

That 5 percent estimate of growth through September is down from about an 8 percent growth that CPPIA in September had estimated for the first half of the year. It could indicate a poor third quarter, or it could reflect difficulty in getting accurate data in China.

Still, in an interview after his speech, Qian said the economic situation seems to be improving in the fourth quarter, and he hoped that industry growth in production could hit 7 percent for the full year.

There have been some recent signs of a pickup in China’s broader manufacturing economy. The widely watched HSBC Purchasing Managers Index for October said output in Chinese factories increased at the strongest rate in seven months, although it cautioned it was a slight increase.

Another industry official at the conference, Lin Jian of the Guangdong Light Industrial Association, said China’s private sector continues to suffer from difficulty getting bank loans. It’s easier for state-owned companies to obtain bank loans, he said in an interview on the sidelines of the conference.

CPPIA’s Qian contrasted the processing industry with China’s plastics equipment manufacturers, which he said have a better global position because of improving technology and a cost advantage, relative to other major machinery manufacturing countries. The technology gap between Chinese and other major producers is shrinking, he believes.

“We can say that we are not that far behind other major countries in our machinery technology,” he said.


Comments

Growth slows sharply for China's plastics processors

By Steve Toloken
Staff Reporter / Asia Bureau Chief

Published: November 8, 2013 12:46 pm ET
Updated: November 8, 2013 12:48 pm ET

Post Your Comments


Back to story


More stories

Image

Keep up with China's rapid changes

July 31, 2014 10:33 am ET

In many ways, 1989 was a very special year in history. Plastics News was launched in Akron. Half a world away, China was trying to carry on economic...    More

Image

Chinese auto suppliers growing in US

July 24, 2014 4:17 pm ET

Two China-based automotive suppliers are expanding in the U.S., according to information released by the Michigan Economic Development Corp.    More

Image

Asia to remain chemical giant but US shale will bring competition

July 23, 2014 1:00 pm ET

A new IHS Chemical report on global spending for chemical production predicts capacity additions will peak in 2014 at $120 billion and then will...    More

Image

Super typhoon ravages South China

July 21, 2014 3:58 pm ET

Super Typhoon Rammasun, the most powerful typhoon that has landed in China in four decades, has left parts of South China devastated, and the local...    More

Image

Windmöller & Hölscher looking to continued growth in China

July 21, 2014 3:40 pm ET

With 2013 global sales of 600 million euros, China has grown into an important export market for Windmöller & Hölscher KG, second only to the United S...    More

Market Reports

Pipe, Profile & Tubing Extrusion in North America 2014

U.S. demand for extruded plastics is expected to grow by 3 percent in 2014, with PVC remaining the largest segment.

Plastic pipe will post the strongest gains through 2018, continuing to take market share from competing materials in a range of markets.

Our latest market report provides in-depth analysis of current trends and their financial impact on the pipe, profile and tubing extrusion industry in North America.

Learn more

2014 Injection Molding Industry Report

GROWTH, OPPORTUNITY IN SIGHT FOR INJECTION MOLDERS IN 2014

In the wake of the economic turbulence earlier in this decade, molders today find themselves in much better shape. Molders are gaining a competitive advantage by investing in people, equipment and seeking inroads into new markets on a global scale.

Growth in the injection molding industry is going to be driven by low financing costs and a continued move to reshore some business.

Learn more

Shale Gas Market - Analysis of North American Region

This report highlights the impact of shale-based natural gas on the North American plastics market and features an in-depth analysis of production trends in the United States during 2013 and a forecast for 2014 and beyond.

Learn more

Upcoming Plastics News Events

September 10, 2014 - September 12, 2014Plastics Caps & Closures 2014

January 14, 2015 - January 14, 2015Plastics in Automotive

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

More Events