Battery bottlenecks delay Mitsubishi plug-in hybrid launch

Hans Greimel
AUTOMOTIVE NEWS

Published: December 30, 2013 3:18 pm ET
Updated: December 30, 2013 3:25 pm ET

Related to this story

Topics Sustainability, Automotive

TOKYO -- Mitsubishi Motors Corp. has delayed the U.S. launch of its Outlander plug-in hybrid until 2015, two years after its global debut, because of bottlenecks in battery production.

The company is ramping up battery supply, but it won't be enough to start U.S. deliveries of the electrified crossover next year as planned.

Mitsubishi President Osamu Masuko said the problem is tight capacity at its main battery supplier, Lithium Energy Japan. The company is a joint venture between Mitsubishi Motors, Japanese battery maker GS Yuasa Corp. and trading house Mitsubishi Corp.

Until this fall, Mitsubishi was getting only 2,000 battery packs a month from LEJ because the supplier was splitting production between batteries for the Outlander plug-in and batteries for Mitsubishi's i electric vehicle, which is sold as the i-MiEV in Japan.

But in September, LEJ shifted production of EV batteries to a separate plant, freeing capacity at the first plant for more Outlander plug-in hybrid batteries.

Mitsubishi now can get 4,000 plug-in battery packs a month and expects that to increase to 5,000 a month in April, when LEJ expands capacity again. Masuko: Three-year business plan

"That means about 60,000 units annually for the plug-in," Masuko said in an interview. "We can make only 30,000 plug-in vehicles this year. It's going to be double."

The gasoline version of the Outlander arrived in the United States in July.

The hybrid variant, which hit showrooms in Japan last January, is a key element of Mitsubishi's effort to rebrand itself as a leader in electrified drivetrains. Adding sales in the United States would help drive volume and reduce costs, while giving U.S. Mitsubishi dealers a badly needed addition to a thin lineup.

Mitsubishi has sold 11,300 plug-in Outlanders globally since January: 8,100 in Japan and 3,200 in Europe. That compares with 74,400 gasoline versions sold worldwide.

Sales of the plug-in were dented by a battery recall that forced Mitsubishi to stop producing the vehicle from late March until late August.

A problem with LEJ batteries forced Mitsubishi to recall more than 4,000 Outlander plug-ins and i-MiEVs in Japan in June.

The defective batteries were prone to short-circuiting for two reasons. In some instances, workers dropped the batteries, causing parts of the battery cells to break off and contaminate the cells. In other cases, a screening process applied excessive force to the batteries, which also caused internal damage to the cells.

Masuko said another increase in battery output is needed after April to buttress the U.S. launch of the plug-in, though he declined to give a U.S. sales forecast.

Mitsubishi needs to ramp up battery sourcing quickly.

Under a three-year business plan unveiled last month, Masuko aims to add plug-in variants of the Outlander Sport compact crossover and Pajero SUV by the spring of 2017.

Mitsubishi has not said where it will get those batteries. But a spokesman said the company is open to expanding its supply base beyond LEJ.

The company currently gets a limited supply of lithium ion battery packs from Toshiba Corp. that are used in a low-trim version of the i-MiEV electric car sold in Japan.

Last month Mitsubishi also signed a deal with the Nissan-Renault Alliance to cooperate on developing a future compact EV and electrified drivetrain technologies.


Comments

Battery bottlenecks delay Mitsubishi plug-in hybrid launch

Hans Greimel
AUTOMOTIVE NEWS

Published: December 30, 2013 3:18 pm ET
Updated: December 30, 2013 3:25 pm ET

Post Your Comments


Back to story


More stories

Image

Plastics help Volt hit new target

January 28, 2015 1:54 pm ET

The 2016 Volt, unveiled at the North American International Auto Show in Detroit in January, features a sportier exterior design — GM calls it...    More

Image

FPI joins curbside recycling group

January 28, 2015 11:47 am ET

Foodservice Packaging Institute is joining the board of the Curbside Value Partnership, a non-profit group that works to improve curbside recycling...    More

Image

Agricultural container recycling grows

January 28, 2015 11:42 am ET

Plastic pestitcide container recycling shot up by nearly 40 percent last year, according to new statistics from the Virginia Department of...    More

Image

PC used in academy roof retrofit

January 28, 2015 8:55 am ET

Polycarbonate sheet meets the demands of a “living roof” in a retrofit at the California Academy of Sciences in San Francisco.    More

Image

China's plastics industry making a shift

January 27, 2015 3:41 pm ET

China's plastic industry is in the midst of a “profound adjustment” from large-scale and high-speed growth to growth focused on quality, e...    More

Market Reports

Plastics in Automotive: Innovation & Emerging Trends

This special report newly released by PN and sponsored by The Conair Group examines current trends in the use of plastics in automotive, materials innovations and the changing landscape. It includes a review of legislative/regulatory activity impacting vehicle development and lightweighting, market opportunities & challenges for mold and toolmakers, innovative design strategies being implemented by major OEMs and suppliers, as well as a review of key indicators in Canada, Mexico, Brazil and China.

Learn more

Plastics Recycling Trends in North America

This report is a review and analysis of the North American Plastics Recycling Industry, including key trends and statistics based on 2013 performance. We examine market environment factors, regulatory issues, industry challenges, key drivers and emerging trends in post-consumer and post-industrial recycling.

Learn more

Injection Molding Market Analysis & Processor Rankings

Plastics News BUNDLED package contains our in-depth Market Analysis of the Injection Molding segment. You will gain keen insight on current trends and our economic outlook.

As a BONUS this includes PN's updated 2014 database of North American Injection Molders RANKED by sales volume. Sort, merge, mail & prospect by end market, materials processed, region, # of plants and more.

Learn more

Upcoming Plastics News Events

February 4, 2015 - February 6, 2015Plastics News Executive Forum 2015

June 2, 2015 - June 3, 2015Plastics Financial Summit - Chicago 2015

September 16, 2015 - September 18, 2015Plastics Caps & Closures - September 2015

More Events